ITT-made Sport, Military and Law-Enforcement Gear

Most consumer night vision products are light amplifying devices. All ITT Industries Night Vision products use light-amplifying technology. This technology takes the small amount of light that's in the surrounding area (such as moonlight or starlight), and converts the light energy (scientists call it photons) into electrical energy (electrons).

These electrons pass through a thin disk that's about the size of a quarter and contains more than 10 million channels. As the electrons go through the channels, they strike the channel walls and thousands more electrons are released. These multiplied electrons then bounce off of a phosphor screen which converts the electrons back into photons and lets you see an impressive nighttime view even when it's really dark.

Automatic Brightness Control (ABC)
An electronic feature that automatically reduces voltages to the microchannel plate to keep the image intensifier's brightness within optimal limits and protect the tube. The effect of this can be seen when rapidly changing from low-light to high-light conditions.; the image gets brighter and then, after a momentary delay, suddenly dims to a constant level. Also called "Highlight Cutoff"

Black Spots
These are common blemishes in the image intensifier or can be dirt or debris between the lenses. Black spots that are in the image intensifier do not affect the performance or reliability of a night vision device and are inherent in the manufacturing processes. Every night vision image intensifier tube is different.

Biocular
Viewing a single image source with both eyes (example: watching a television set).

Binocular
Viewing a scene through two channels; i.e. one channel per eye.

Blooming
Momentary loss of the night vision image due to intensifer tube overloading by a bright light source. When such a bright light source comes into the night vision device's view, the entire night vision scene becomes much brighter, "whiting out" objects within the field of view. Blooming is common in Generation 0 and 1 devices.

Bright-Source Protection (BSP)
An electronic function that reduces the voltage to the photocathode when the night vision device is exposed to bright light sources such as room lights or car lights. BSP protects the image tube from damage and enhances its life; however, it also has the effect of lowering resolution when functioning.

Boresighting
The alignment of a weapon aiming device to the bore of the weapon. See also Zeroing.

C-Mount
A standard still and video camera lens thread size for mounting to the body of a camera. Usually 1/2" or 3/4" in diameter.

COMSPEC (Commercial Specification)
A term used to describe image tube quality, testing and inspection done by the original equipment manufacturer (OEM).

Daylight Lens Cover
Usually made of soft plastic or rubber with a pinhole that allows a small amount of light to enter the objective lens of a night vision device. This should be used for training purposes only, and is not recommended for an extended period of time.

Daylight Training Filter
A glass filter assembly designed to fit over the objective lens of a night vision device. The filter reduces light input to a safe (night-time) level, allowing safe extended daytime use of the night vision device.

Diopter
The unit of measure used to define eye correction or the refractive power of a lens. Usually, adjustments to an optical eyepiece accomodate for differences in individual eyesight. Most ITT systems provide a +2 to -6 diopter range.

Distortion
There are two types of distortion found in night vision systems. One type is caused by the design of the optics, or image intensifier tube, and is classical optical distortion. The other type is associated with manufacturing flaws in the fiber optics used in the image intensifier tube.

* Classical Optical Distortion: Classical optical distortion occurs when the design of the optics or image intensifier tube causes straight lines at the edge of the field of view to curve inward or outward. This curving of straight lines at teh edge will cause a square grid pattern to start to look like a pincushion or barrel. This distortion is the same for all systems with the same model number. Good optical design normally makes this distortion so low that the typical user will not see the curving of the lines.

* Fiber Optics Manufacturing Distortions: Two types of fiber optics distortions are most significant to night vision devices: S-distortion and shear distortion:

- S-Distortion: Results from the twisting operation in manufacturing fiber-optic inverters. Usually S-distortion is very small and is difficult to detect with the unaided eye.
- Shear Distortion: Can occur in any image tube that use fiber-optic bundles for the phospor screen. It appears as a cleavage or dislocation in a straight line viewed in the image area, as though the line were "sheared".

Equivalent Background Illumination (EBI)
This is the amount of light you see through a night vision device when an image tube is turned on but not light is on the photocathode. EBI is affected by temperature; the warmer the night vision device, the brighter the background illumination. EBI is measured in lumens per square centimeter (lm/cm2). The lower the value the better. The EBI level determines the lowest light level at which an image can be detected. Below this light level, objects will be masked by the EBI.

Emission Point
A steady or fluctuating pinpoint of bright light in the image area that does not go away when all light is blocked from the objective lens. The position of an emission point within the field of view will not move. If an emission point disappears or is only faintly visible when viewing under brighter nighttime conditions, it is not indicative of a problem. If the emission point remains bright under all lighting conditions, the system needs to be repaired. Do not confuse an emission point with a point of light source in the scene being viewed.

Eye Relief
The distance a person's eyes must be from the last element of an eyepiece in order to achieve the optimal image area.

Field-of-View
The diameter of the imaged area when viewed through an optic

Figure of Merit (FOM)
Image Intensification tube specification designation, calculated on line pair per mm x signal to noise.

Fixed-Pattern Noise (FPN)
A faint hexagonal (honeycomb) pattern throughout the image area that most often occurs under high-light conditions. This pattern is inherent in the structure of the microchannel plate and can be seen in virtually all Gen 2 and Gen 3 systems if the light level is high enough.

Footlambert(fL)
A unit of brightness equal to one footcandle at a distance of one foot.

Gain
Also called brightness gain or luminance gain. This is the number of times a night vision device amplifies light input. It is usually measured as tube gain and system gain. Tube gain is measured as teh light output (in fL) divided by the light input (in fc). This figure is usually expressed in values of tens of thousands. If tube gain is pushed too high, the tube will be "noiser" and the signal-to-noise ration many go down. U.S. military Gen 3 image tubes operate at gains of between 20,000 and 45,000. On the other hand, system gain is measured as teh light output (fL) divided by the light input (also fL) and is what the user actually sees. System gain is usually seen in the thousands. U.S. military systems operate at 2,000 to 3,000. In any night vision system, the tube gain is reduced by the system's lenses and is affected by the quality of the optics or any filters. Therefore, system gain is a more important measurement to the user.

Gallium Arsenide (GaAs)
The semiconductor material used in manufacturing the Gen 3 photocathode. GaAs photocathodes have a very high photosensitivity in the spectral region of about 450 to 950 nanometers (visible and near-infrared region).

Generations
Two technologies are referenced as night vision; image intensification and thermal imaging (see definitions). Because of cost and the fact that image intensifier scenes are easier to interpret than thermal (thermal images show targets as black or white - depending upon temperature - making it more difficult to recognize objects), the most widely used night vision aid in law enforcement is image intensification (l²) equipment. Developments in the l² technology are categorized in terms of "generations". To date, there have been four generations of l² devices, identified as Gen 0, Gen 1, Gen 2, and Gen 3. Developmental laboratory work is on-going, and the U.S. military may designate the resulting as Gen 4. However, no definition for Gen 4 presently exists.

Generation 0
The first night vision aids (also called Generation Zero or Gen 0) were sniper scopes that came into use during World War II and the Korean conflict. These were not true image intensifiers, but rather image converters, which required a source of invisible infrared (IR) light mounted on or near the device to illuminate the target area.

Generation 1
The "starlight scopes" developed during the early 1960's for use in Vietnam were the first Generation (Gen 1) of image intensifier devices. In Gen 1 night vision units, three image intensifiers were connected in a series, making the units longer and heavier than future night vision units would be. Gen 1 equipment produced an image that was clear in the center of the field of view but suffered from large optical distortion around the periphery. Gen 1 equipment was also subject to "blooming". Most low-cost imported night vision units use Gen 1 technology, though often under the guise of a higher "generation".

Generation 2
The development of the microchannel plate, or MCP, in the late 1960s brought on the second generation (Gen 2) in l² night vision. The MCP accelerated and multiplied electrons which provided the gain previously supplied by coupling three image intensifiers together (Gen 1). The introduction of the MCP significantly reduced size and weight for image intensifier tubes, enabling design of smaller night vision goggles and hand-held devices. The MCP also provided much more robust operation when bright lights entered the field of view. The Gen 2 tubes used the same tri-alkali photocathode as the Gen 1 devices. This generation was implemented to reflect the change in how the light was amplified (MCP versus three-stage coupling).

See Generation 2 Night Vision Goggles, Monoculars & Weapon Sights

Generation 3
Third-generation (Gen 3) image intensifiers were developed in the mid-1970s and became available during the early 1980s. Gen 3 introduced two major technological improvements: the gallium arsenide (GaAs) photocathode and the ion barrier coating to the microchannel plate. The GaAs photocathode increases the tube's sensitivity to light from the near-infrared range of the spectrum, enables it to function at greater detection distances, and improves system performance under low-light conditions. Application of a metal-oxide ion barrier to the MCP increases the life of the image tube. The operational life of Gen 3 tubes is in excess of 10,000 hours, compared to that of Gen 2 tubes which is about 2,000 to 4,000 hours. This generation was implemented to reflect the change in the photocathode (tri-alkali replaced with GaAs).

Highlight Shutoff
An image intensifier protection feature incorporating a sensor, microprocessor and circuit breaker. This feature will turn the system off during periods of extreme bright light conditions.

Interpupillary Adjustment
The distance between the user's eyes (pupils) and the adjustment of binocular optics to adjust for differences in individuals. Improperly adjusted binoculars will display a scene that appears egg-shaped or as a reclining figure-8.

Interpupillary Distance
The distance between the user's pupils (eyeball centres). The 95th percentile of US military personnel falls within the 55 to 72mm range of IPD.

IR Illuminator
Many night vision devices incorporate a built-in infrared (IR) diode that emits invisible light or the illuminator can be mounted on to it as a separate component. IR light cannot be seen by the unaided eye; therefore, a night vision device is necessary to see this light. IR Illuminators provide supplemental infrared illumination of an appropriate wavelength, typically in a range of wavelengths (e.g. 730nm, 830nm, 920nm), and eliminate the variability of available ambient light, but also allow the observer to illuminate only specific areas of interest while eliminating shadows and enhancing image contrast.

IR Laser
High-power devices providing long-range illumination capability. Ranges of several thousand meters are common. Most are not eye-safe and are restricted in use. Each IR laser should be marked with a warning label like the one shown here. Consult FDA CFR Title 21 for specific details and restrictions.

I2 (Image Intensification) Collects and intensifies the available light in the visible and near-infrared spectrum. Offers a clear, distinguishable image under low-light conditions.

IR (Infrared) Area outside the visilbe spectrum that cannot be seen by the human eye (between 700 nanometers and 1 millimeter). The visible spectrum is between 400 and 700 nanometers.

Ip/mm (Line Pairs per Millimeter) Units used to measure image intensifier resolution. Usually determined from a 1951 U.S. Air Force Resolving Power Test Target. The target is a series of different-sized patterns composed of three horizontal and three vertical lines. A user must be able to distinguish all the horizontal and vertical lines and the spaces between them. Typically, the higher the line pair, the better the image resolution. Generation 3 tubes generally have a range of 64 - 72 lp/mm, although line pair measurement does not indicate the generation of the tube. Some Generation 2+ tubes measure 28-38 lp/mm, while a Generation 1+ tube may have measure at 40 lp/mm.

Lumen: Denotes the photons perceptible by the human eye in one second.

Monocular
A singlechannel op-tical device. The American Eagle in this catalogue is an example of a monocular

NATO-STANAG
Term for the North Atlantic Treaty Organization STANdard AGreement. This can be described as an international MILSPEC

mA/W (Milliamps per Watt):
The measure of electrical current (mA) producted by a photocathode when exposed to a specified wavelength of light at a given radiant power (watt).

MCP (Microchannel Plate):
A metal-coated glass disk that mulitplies the electrons produced by the photocathode. An MCP is found only in Gen 2 or Gen 3 systems. MCPs eliminate the distortion characteristic of Gen 0 and Gen 1 systems. The number of holes (channels) in an MCP is a major factor in determining resolution. ITT Industries' MCPs have 10.6 million holes or channels compared to the previous standard of 3.14 million.

Near-Infrared:
The shortest wavelengths of the infrared region, nominally 750 to 2,500 nanometers. Also see IR (infrared).

Photocathode:
The input surface of an image intensifier tube that absorbs light energy (photons) and in turn releases electrical energy (electrons) in the form of an image. The type of material used is a distinguishing characteristic of the different generations.

Photocathode Sensitivity:
Photocathode sensitivity is a measure of how well the image intensifier tube converts light into an electronic signal so it can be amplified. The measureing units of photocathode sensitivity are micro-amps/lumen (µA/lm) or microamperes per lumen. This criterion specifies the number of electrons released by the Photocathode (PC). PC response is always measured in isolation with no amplification stage or ion barrier (film). Therefore, tube data sheets (which always carry this “raw” figure) do not reflect the fact that over 50% of those electrons are lost in the ion barrier. While for most latest 3rd generation image intensifiers the photoresponse is in the 1800 µA/lm (2000 µA/lm for the latest Omni VI Pinnacle tubes), the actual number is more like 900 µA/lm. The 4th generation DOES NOT use ion barrier and while its “raw” photoresponse is the same as 3rd, the actual number is actually 100% higher.

Resolution
The ability of an image intensifier or night vision system to distinguish between objects close together. Image intensifier resolution is measured in line pairs per millimetre (lp/mm) while system resolution is measured in cycles per miliradian. For any particular night vision system, the image intensifier resolution will remain constant while the system resolution can be affected by altering the objective or eyepiece optics by adding magnification or relay lenses. Often the resolution in the same night vision device is very different when measured at the centre of the image and at the periphery of the image. This is especially important for devices selected for photograph or video where the entire image resolution is important. Measured in line pairs per millimetre (lp/mm).

Reticle (Reticle Pattern)
An adjustable aiming point or pattern (i.e. crosshair) located within an optical weapon sight

Signal-to-Noise Ratio (SNR)
A measure of the light signal reaching the eye divided by the perceived noise as seen by the eye. A tube's SNR determines the low-light-resolution of the image tube; therefore, the higher the SNR, the better the ability of the tube to resolve objects with good contrast under low-light conditions. Because SNR is directly related to the photocathode's sensitivity and also accounts for phosphor efficiency and MCP operating voltage, it is the best single indicator of an image intensifier's performance

Scintillation
Also known as electronic noise. A faint, random, sparkling effect throughout the image area. Scintillation is a normal characteristic of microchannel plate image intensifiers and is more pronounced under low-light-level conditions

Screen
The image tube output that produces the viewable image. Phosphor (P) is used on the inside surface of the screen to produce the glow, thus producing the picture. Different phosphors are used in image intensifier tubes, depending on manufacturer and tube generation. P-20 phosphor is used in the systems offered in this catalogue

Stereoscopic Night Vision
When two views or photographs are taken through one device. One view/photograph represents the left eye, and the other the right eye. When the two photographs are viewed in a stereoscopic apparatus, they combine to create a single image with depth and relief. Sometimes this gives two perspectives, but typically the perspectives are less the further away the object of focus is.

System Gain
Equal to tube gain minus losses induced by system components such as lenses, beam splitters and filters.

Variable Gain Control
Allows the user to manually adjust the gain control ( basically like a dim control ) in varying light conditions. This feature sets the PVS-14 apart from other popular monoculars that do not offer this feature.

Weaver Mounting System
A US weapon mounting system used for attaching sighting devices to weapons. A Weaver Rail is a weapon-unique notched metal rail designed to receive a mating throw-lever or Weaver Squeezer attached to the sighting device

Zeroing
A method of boresighting an aiming device to a weapon and adjusting to compensate for projectile characteristics at known distances.

Glossary courtesy Morovision/ITT